【法规名称】
【法规编号】 68853 什么是编号？
【正 文】
第6页 CAP 374F ROAD TRAFFIC (SAFETY EQUIPMENT) REGULATIONS
|
[接上页] (L.N. 37 of 1989; L.N. 288 of 1995; L.N. 262 of 1996; L.N. 162 of 2000) Cap 374F reg 11 (Repealed) (Repealed 89 of 1994 s. 28) Cap 374F reg 12 Offences (1) Any person who contravenes regulation 3, 4, 7(1) or (2), 7A(1) or (2), 7B(1) or (5) or 8B commits an offence and is liable to a fine of $5000 and to imprisonment for 3 months. (L.N. 37 of 1989; L.N. 162 of 2000) (2) Any person who uses or causes or permits to be used on a road a vehicle which does not comply with any of the requirements of regulation 6, 6A, 6B, 6C, 8A or 9 commits an offence and is liable to a fine of $5000 and to imprisonment for 3 months. (L.N. 148 of 2002) (3) Any driver of- (a) a private car, who contravenes regulation 7(3) or 7B(2), (3) or (6); or (b) a private light bus or goods vehicle, who contravenes regulation 7A(3), (L.N. 148 of 2002)without reasonable excuse, commits an offence and is liable to a fine at level 1. (L.N. 162 of 2000) (L.N. 288 of 1995; L.N. 262 of 1996) Cap 374F Sched 1 APPROVED PROTECTIVE HELMETS [regulation 2] (L.N. 148 of 2002) 1. Protective helmets bearing a marking applied by the manufacturer indicating compliance with the specifications contained in- (a) British Standard 2495; (b) Japanese Industrial Standard JIS T 8133-1970; (c) Australian Standard E 33-1968; (d) American National Standards Institute Z90.1-1966, Z90.1-1970 and Z90.1-1971; (e) Institute Belge De Normalization BENOR NBN 626; (f) Deutsche Normen DIN 4848; (g) French National Standard AFNOR NFS 72-301; (h) Dutch National Institute for Road Vehicles TNO; (i) Snell Memorial Foundation. Standard for Protective Headgear 1970; (j) Safety Helmet Council of America (SHCA) Certification; (k) British Standard 5361. 2. Protective helmets of a type approved by the Commissioner, bearing a marking determined by him indicating that the type of helmet has been accepted as capable of affording to persons riding motor cycles a degree of protection from injury equal to or greater than that provided by protective helmets of the types specified in paragraph 1. Cap 374F Sched 2 APPROVED SEAT BELTS AND APPROVED ANCHORAGE POINTS [regulation 2] (L.N. 148 of 2002) PART I Approved Seat Belts 1. Seat belts in respect of which either the seat belt assembly or the vehicle to which it is attached is permanently marked by the manufacturer of the belt or vehicle with the specification number, mark or symbol indicating compliance with any of the following- (a) British Standard for Seat Belt Assemblies for motor vehicles BS 3254: 1960 and BS 3254, including Part 1: 1988 Specification for restraining devices for adults; and BS 3254, including Part 2: 1991 Specification for restraining devices for children; (b) British Standard Specification for Passive Seat Belt Systems BS AU 160a and BS AU 183: 1989; and BS AU 157a, BS AU 185, BS AU 186, BS AU 186a, BS AU 202 and BS AU 202a for child restraint system; (c) ECE Regulation No. 16 made by the Economic Commission for Europe dated 7 May 1973 including all Revisions for Seat Belt made before the date this paragraph comes into operation; and ECE Regulation No. 44 made by the Economic Commission for Europe dated 1 February 1981 including all Revisions for restraining devices for children made before the date this paragraph comes into operation; (d) Australian Standards for Seat Belt Assemblies for motor vehicles E35-1965, E35, Part I-1970 and E35, Part II-1970 (including retractors), including modification authorized by Australian Design Rules No. 4, 4A, 4B and 4C; AS 2596-1995 and 2596-1983, including modifications complying with Australian Design Rule No. 4; and AS 1754-1995 for restraining devices for children; (e) New Zealand Specification for Seat Belt Assemblies for motor vehicles NZS 1662: 1969 and NZS 5401; and NZS 5411 for restraining devices for children; (f) Federal Motor Vehicle Safety Standard (USA) No. 209 for Seat Belt; and No. 213 for restraining devices for children; and (g) Japanese Industrial Standard JIS D4604: 1969 (three-point belts only) and D4604: 1988; and JIS D0401: 1990 and JIS D0401: 1996 for restraining devices for children. 2. Seat belts of a type approved by the Commissioner and specified by him by notice in the Gazette, bearing a marking determined by the Commissioner indicating that the type of seat belt has been accepted as capable of affording to persons in a motor vehicle a degree of protection from injury equal to or greater than that provided by seat belts of the types specified in paragraph 1. (L.N. 114 of 1998) PART II Approved Anchorage Points for Vehicles other than Goods Vehicles and Public Light Buses Registered on or after Specified Date (L.N. 37 of 1989; L.N. 148 of 2002) (a) British Standard for Seat Belt Anchorage Points-B.S. AU48:1965; (b) British Standard for Seat Belt Anchorage Points B.S. AU48a; (c) Japanese Standard JASO-6602; (d) Federal Motor Vehicle Safety Standard (USA) No. 210; (e) E.C.E. Regulation No. 14, including Revision 1, made by the Economic Commission for Europe dated 30 January 1970 and published by the United Nations; |
- 此法规有错误，我来纠正。请点击在此 提交错误内容或者您纠正的内容！